产品分类

solidgoldfx ZETA DLX - OVERDRIVE/PREAMP 过载 前级 单块效果器

吉他音色是个矛盾的问题。我们吉他手有时被迫在好音色和实用性之间做出选择。现在,我们不必选择,因为我们有zeta dlx。 zeta dlx结合了三个最有用的技巧在增益为基础的音调世界:前级、过载和激励。Zeta DLX的整个系统包括一个前置放大器电路,因此,即使您需要直接连调音台,或者前级在现上受到限制,都可以保持您的音色质量。 Zeta DLX的左侧提供了一个过载单元,对所有参数进行了非常广泛的设置,从刺耳的激励到破碎感的过载。三个切换开关为您提供了根据您的个人需要定制zeta dlx的选项。mids和body开关允许您调整特定频带的范围,而clip开关允许您更改剪裁特性。一个额外的微调甚至可以让你调整电路的整体增益。

  • 型号: ZETA DLX
  • 价格:
  • 产地: 加拿大

solidgoldfx ZETA DLX - OVERDRIVE/PREAMP 

过载 前级 单块效果器

图片关键词

       吉他音色是个矛盾的问题。我们吉他手有时被迫在好音色和实用性之间做出选择。现在,我们不必选择,因为我们有zeta dlx。

       zeta dlx结合了三个最有用的技巧在增益为基础的音调世界:前级、过载和激励。Zeta DLX的整个系统包括一个前置放大器电路,因此,即使您需要直接连调音台,或者前级在现上受到限制,都可以保持您的音色质量。

      Zeta DLX的左侧提供了一个过载单元,对所有参数进行了非常广泛的设置,从刺耳的激励到破碎感的过载。三个切换开关为您提供了根据您的个人需要定制zeta dlx的选项。mids和body开关允许您调整特定频带的范围,而clip开关允许您更改剪裁特性。一个额外的微调甚至可以让你调整电路的整体增益。      

      zeta dlx的右侧是JFET,它配备了单独可选择的boost功能,带有一个旋钮来控制音量。音色开关让你控制低音频率的提高,而PRE前置/POST后置让你选择是否提高之前或之后的过载电路。当你试图获得一个超饱和或更粗版本的过载音色是,使用这个单元的效果非常好。

操控:

Volume 音量

Tone:音色

Gain:增益

Level:激励电平

Post/Pre拨杆:后置/前置拨杆

Tone拨杆:左侧原始低频  居中切低频  右侧低频激励

Body拨杆:过载通道中的低频设置,功能与上述TONE相同

Mids拨杆:中频拨杆,从左到右为平滑/激励/无激励 

Clip拨杆:过载通道的波形裁切设置,左侧选择锗管的压缩感音色,右侧是硅管的嘶嘶声动态,中间的位置是一个原始的音色。

Gain (trimpot)侧向开关:调节整体失真电路增益度。

供电:标准9VDC 30ma

尺寸:4.67" x 3.68" x 1.18" (119mm x 94mm x 30mm)

原文介绍:

Guitar tone is tricky business. We guitarists are sometimes forced to choose between great tone and utility. In our case, we don’t have to choose, because we have the Zeta DLX. Are you also tired of choosing? Venture ahead, brothers and sisters of tone.

The Zeta DLX combines three of the most useful tricks in the gain-based tonal world: Preamp, drive and boost. The entirety of the Zeta DLX comprises a preamp circuit, so that you can keep your tone fresh even if you have to go direct, or your amp options are limited on fly-out gigs. However, each since each side is individually switchable, we must look at the sum of the parts.

The left side of the Zeta DLX serves up a generous drive circuit that has extremely wide sweeps of all the parameters, from jangly boost to crunchy OD. Three of the toggle switches give you options to tailor the Zeta DLX to your individual needs. The Mids and Body toggles allow you to adjust the range of those particular frequency bands, while the Clip switch lets you change the clipping characteristics. A bonus trimpot inside even lets you adjust the overall gain of the circuit.

On the right side of the Zeta DLX is the JFET-equipped individually selectable boost function, with a single knob to control the amount. The B. Tone toggle gives you control over the bass frequencies of the boost, while Pre/Post lets you choose whether the boost goes before or after the drive circuit. You can use this to great effect when trying to get either a super-saturated dirt tone or a burlier version of the drive side.

Don’t get caught between a rock and a tonal hard place again—plug into the Zeta DLX and feel the gear instead of just hearing it.

KNOBS:

Volume:

Gives you a tasteful amount of volume on tap, enough to work with all kinds of setups.

Tone:

Adjusts the bass and treble content of the drive side.

Gain:

Adjusts both the amount of overdrive and the amount of treble. As you roll the Gain up, more high end enters the signal path, allowing for clarity within the saturation.

Level:

Governs the amount of boost engaged when in Boost mode. Be careful with this one!

TOGGLE SWITCHES:

Post/Pre:

This switch controls the order of both channels when they are used simultaneously. Toggling this switch puts the Boost before the Drive or vice-versa for two different stacked tones.

Tone:

This three-position toggle controls the level of the bass frequencies pushed by the Boost channel. When set to the left, the bass is the stock value. In the center, you’ll find a bass cut, and the right position is a bass boost.

Body:

Controls the level of the bass frequencies in the Drive channel. The corresponding switch positions are the same as the B. Tone switch above.

Mids:

Adjusts the amount of mids present in the Drive channel. The left position is flat, center position s boosted, and the right position is scooped.

Clip:

This three-position switch controls which type of clipping diodes are present in the drive channel. The left position selects a silicon-germanium hybrid for a bit more compression and crunch, the right position selects silicon parts for a bit more dynamics and sizzle, and the center position removes them altogether for a raw, throaty tone.

UNDER THE HOOD:

Gain (trimpot):

Adjusts the overall gain of the drive channel, and thusly, the range of the external Gain control.

Bias 1 and Bias 2 trimpots are not user-adjustable.

AUXILIARY:

Input:

Instrument or other pedal goes here.

Output:

Amplifier or other pedal goes here.

True bypass footswitches:

Turns corresponding channels on and off.

POWER:

The Zeta DLX requires a center-negative 9VDC power adapter with at least 30mA of current (not included). Almost all power supplies meet this requirement, but check yours beforehand.

DIMENSIONS:

4.67" x 3.68" x 1.18" (119mm x 94mm x 30mm)