产品分类

solidgoldfx SURF RIDER III - SPRING REVERB 混响 单块效果器

对于混响效果器,使用者普遍认为前级的弹簧混响是的混响的顶峰。这也许是正确的,但如果你的前级没有混响功能呢?如果你的扩音器混响不好怎么办?又或者没有一个让我满意的音色没有充分的调节选项?SURF RIDER III (冲浪者)应运而生。 多功能性是SURF RIDER III (冲浪者)名称的含义。LEVEL电平控制只是开始,调整总信号中的混响量。SURF RIDER III 还提供了一个depth深度旋钮,可以调节混响的强度,填补空间感。他还可以通过外接踏板进行表情控制。 Decay衰减控制增加了虚拟混响池的大小,打开效果器,可以很自然底给予缓冲,这些音色似乎永远都在继续。说到音色,有一个方便的tone音色调节旋钮,它可以使混响信号变亮或变暗,这有助于应对各种拾音器的音色特性,比如过亮或者过闷。

  • 型号: SURF RIDER III
  • 价格:
  • 产地: 加拿大

SURF RIDER III - SPRING REVERB   

冲浪者III 混响单块效果器

图片关键词

      对于混响效果器,使用者普遍认为前级的弹簧混响是的混响的顶峰。这也许是正确的,但如果你的前级没有混响功能呢?如果你的扩音器混响不好怎么办?又或者没有一个让我满意的音色没有充分的调节选项?SURF RIDER III (冲浪者)应运而生。

       多功能性是SURF RIDER III (冲浪者)名称的含义。LEVEL电平控制只是开始,调整总信号中的混响量。SURF RIDER III 还提供了一个depth深度旋钮,可以调节混响的强度,填补空间感。他还可以通过外接踏板进行表情控制。

       Decay衰减控制增加了虚拟混响池的大小,打开效果器,可以很自然底给予缓冲,这些音色似乎永远都在继续。说到音色,有一个方便的tone音色调节旋钮,它可以使混响信号变亮或变暗,这有助于应对各种拾音器的音色特性,比如过亮或者过闷。

       Res共振开关可以切换混响的“滴落度”,给你很多(上位置),一点(下位置)或一点都没有(中心)。

       boost 推子可以增强或降低混响级别。LED亮起时,踏板处于Hi(高)模式,OFF(关)为Lo(低)模式。

       让我们一起冲浪吧!

操控及配置

Tone 音色旋钮

调节音色的明暗度

Decay 衰减调节

Depth 混响音色深度、渲染度调节

Level 混响湿信号音量调节

Res 共振模式拨杆  (向上 向下 中心)

内部电路调节:

Res (trimpot) 共振幅度调节

Boost (trimpot)推子幅度调节

踩丁和接口:

Input 输入

Output 输出

Expression jack 拓展踏板

True bypass footswitch 真旁路踩丁开关

Boost footswitch 推子踩丁开关

供电:

标准 9VDC 

53mA工作电流

尺寸规格:

4.67" x 3.68" x 1.18" (119mm x 94mm x 30mm)


Reverb purists often point to amp reverb as being the pinnacle of spring reverb. That may be all well and good, but what if your amp just doesn’t have reverb? What if your amp’s reverb isn’t good? What if you want more options after a simple “level” control? It is time to ride the waves into the Surf Rider III.

The Surf Rider III is the ‘verb sound that Fender’s engineers would have put into their Deluxes and Vibroverbs if they had access to today’s technology. Our finest ‘verb box gives you that familiar Level control but then adds a plethora of options, including a boost and some nifty resonance features that adds some juice to your tank without the springs.

Versatility is the name of the Surf Rider’s game. The Level control is just the beginning, adjusting the amount of reverb in the total signal. The Surf Rider also offers a Depth knob that adjusts the intensity of the reverberations, for some hauntingly huge verbs that fill the room. The expression jack on the side overrides this control, should you feel so inclined.

The Decay control increases the size of the virtual reverb tank, opening up the pedal and giving you verb tones that go on seemingly forever. Speaking of tones, there’s a handy Tone knob that brightens or darkens the reverb signal, which helps tame harsh pickups or beef up flimsy ones. It’s especially helpful if the Surf Rider III is your only pedal—a splendid idea.

The Resonance switch unlocks the “drippiness” of the reverb tank, giving you a lot (upper position), a little (lower position) or none at all (center). Cracking open the Surf Rider III gives you a trimpot to set the lower level for just the right amount of splash.

The Boost section lets you boost or cut the reverb level. With the LED on, the pedal is in Hi mode, and off is Lo mode. There’s another internal trimmer that lets you dial in Lo mode. Surf’s up.

KNOBS:

Tone:

This knob lightens or darkens the frequency of the reverb signal only, from dark and moody to bright and biting.

Decay:

Turning the Decay control up increases the decay time of the reverb signal, giving you access to huge, surf-inspired ‘verbs that linger seemingly forever.

Depth:

Increases the size of the virtual spring tank and the intensity of the signal. When connecting an expression pedal, you can control this knob hands-free.

Level:

Controls the volume of the reverb (wet) signal.

TOGGLE SWITCHES:

Res:

This is a three-position switch that alters the resonance of the tank. The upper position adds a high amount of resonance, while the lower position adds an amount that you set via internal trimpot (see “Under the hood” below). In the center position, the toggle adds no resonance.

UNDER THE HOOD:

Res (trimpot):

This trimpot allows you to adjust the amount of resonance in the reverb signal while in the “Lo” (bottom) position of the Res toggle.

Boost (trimpot):

When the Boost is in the off position (LED off), a portion of the reverb level is reduced. This trimpot lets you adjust how much is reduced to fine-tune the reverb signal.

AUXILIARY:

Input:

Instrument or other pedal goes here.

Output:

Amplifier or other pedal goes here.

Expression jack:

Connecting an expression pedal here gives you hands-free control over the Depth knob.

True bypass footswitch:

Turns the effect on and off.

Boost footswitch:

With the LED on, the Surf Rider III is in “Hi” mode, boosting the reverb signal. With the LED off, the Surf Rider III is in “Lo” mode, and a bit of the reverb level is reduced. You can adjust how much with the Boost trimpot (see above in “Under the hood”).

POWER:

The Surf Rider III requires a center-negative 9VDC power adapter with at least 53mA of current (not included). Almost all power supplies meet this requirement, but check yours beforehand.

 

DIMENSIONS:

4.67" x 3.68" x 1.18" (119mm x 94mm x 30mm)